What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general.

Learn more

PRTG Network Monitor

Intuitive to Use. Easy to manage.
More than 500,000 users rely on Paessler PRTG every day. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free Download

Top Tags


View all Tags

How does PRTG compute CPU Index, Traffic Index and Response Time Index?

Votes:

3

I need more information on how these graphs/indicators are computed, ideally on the basis of a specific example.

cpu-index response-time-index traffic-index

Created on Feb 2, 2010 4:11:45 PM by  Roland Grau [Paessler Support]

Last change on Mar 4, 2022 1:34:00 PM by  Brandy Greger [Paessler Support]



3 Replies

Accepted Answer

Votes:

3

This article applies as of PRTG 22

How does PRTG compute CPU Index, Traffic Index, and Response Time Index?

PRTG provides you with graphs to give you a quick status overview of your network. To do so, it computes so-called Index values based on the measurements of a selection of sensors. The Index graphs are synthetic values ranging from 0% and 100%, based on current sensor measurements and their historic peak values. The index calculation works similarly to a stock index, which is the computed mean value of a stock selection.

For each group and device, PRTG shows four values in a graph:

Graph values

They are based on the measurements of a selection of sensors in that group (or device). The Alarms graph shows the number of alarms at a given moment in history. There are three index values:

  • Response Time Index
  • CPU Load Index
  • Traffic Index

Examples

A CPU Load Index value of 10% for a group means that the average CPU load for a selection of CPU sensors of this group is currently at 10% of the CPU peak (historic maximum) of that group. Usually, for response times the historic maximums are much higher than the average value. For example, for pings in a LAN, a normal time might be 2-10 milliseconds (ms) while a maximum of several hundred ms is not unusual. For this reason, most Response Time Index readings are usually between 10% and 20%.

How does it work?

  • During the regular network monitoring process, PRTG records the highest value ever measured for each sensor.
  • The currently measured value is weighted against this upper liminal value to compute an index value for a sensor between 0% and 100%.
  • For each device, the index values for CPU load sensors, traffic sensors, and sensors that measure response times are combined.
  • For each group, the index values of all devices are combined.

Keep in mind that changing the sensor setup (the number and types of sensors) also inevitably changes the index values because the numeric base for the calculation changes. This means that values before and after a configuration change may not be comparable at all. The same applies to situations where one or more sensors cannot be monitored (for example, when a probe is disconnected).

Created on Feb 2, 2010 4:12:27 PM by  Roland Grau [Paessler Support]

Last change on Jan 4, 2023 9:50:47 AM by  Brandy Greger [Paessler Support]



Votes:

0

By the logic of the measurement of index values, historical peak is used. What happens when the current peak exceeds historic peak? Ideally at the moment past breach is broken, the index should cross 100% until the current peak replaces the past one.

The other way to look at this is at the moment the historical peak is breached the current peak becomes the new norm with index showing 100%.

When we say historical peak, how old that peak can be? Are the current data points getting more weightage leading to recent lower peaks replacing the past peaks as they fade into history.

Created on Mar 9, 2020 5:46:49 PM



Votes:

0

Hello there,

If a value is recorded that is higher then the previous maximum value, then this new value becomes the new maximum. The maximum values should be stored as long as the sensor data is stored (per default 1 year). For more information about how long data is being stored, please see our manual about Historic Data Purging.

Created on Mar 10, 2020 9:45:46 AM by  Sasa Ignjatovic [Paessler Support]




Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.