New Question
 
 
PRTG Network Monitor

Intuitive to Use.
Easy to manage.

300.000 administrators have chosen PRTG to monitor their network. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free PRTG
Download >>

 

What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general. You are invited to get involved by asking and answering questions!

Learn more

 

Top Tags


View all Tags


WMI problem after latest version update?

Votes:

0

Your Vote:

Up

Down

After upgrading to the latest PRTG version this moring, the local and cluster probe health has been in a warning (and sometimes down) state. With the following error;

"104 % Delay (Probe Interval Delay WMI) is above the error limit of 100 % Delay. WMI Sensors of this probe can not be scanned in their specified intervals. Try longer intervals or distribute load over probes."

We have increased the scan interval from 5 minutes to 10, this had no effect.

It seems to tie in to the amount of "Probe open requests" and increase in the "Available memory", which doesnt seem to make much sense.

Regards

Richard

sensor v12 wmi

Created on Jun 26, 2012 8:35:03 PM by  Mark Betham (0) 1



7 Replies

Votes:

0

Your Vote:

Up

Down

Hi,
what precise version are you using? If not done yet, please perform a upgrade to the most recent version 12.2.2.2157 which should fix the issue.
Best regards

Created on Jun 27, 2012 6:55:29 AM by  Konstantin Wolff [Paessler Support]



Votes:

0

Your Vote:

Up

Down

Hi,

We started to see these issues after upgrading to PRTG Network Monitor 12.2.2.2157

Regards

Rich

Created on Jun 27, 2012 7:06:55 AM by  Mark Betham (0) 1



Votes:

0

Your Vote:

Up

Down

Hi,
please send your PRTG logs and Probe States to [email protected] and refer to this KB entry. The logs are to be found in <PRTG Data Directory>\Logs (System) and your Probe States can be written in the WebGUI under Setup -> System Status -> Write Probe States. The Probe States are also placed in the Logs Directory.
Best regards

Created on Jun 27, 2012 7:18:36 AM by  Konstantin Wolff [Paessler Support]



Votes:

0

Your Vote:

Up

Down

The logs and Probe States should be written to;

C:\Paessler\PRTG Network Monitor\Logs (System)\

However the only item in that directory is a blank text file "PRTGValidate.txt" (Modified 28/05/2012)

Please advise.

Created on Jun 27, 2012 7:30:19 AM by  Mark Betham (0) 1



Votes:

0

Your Vote:

Up

Down

Hi, please open the program "PRTG Server Administrator" and there switch to the tab "Logs". You can either send the logs directly from there or open the logfile directory also.
Best regards

Created on Jun 27, 2012 7:36:04 AM by  Konstantin Wolff [Paessler Support]



Votes:

0

Your Vote:

Up

Down

Hi, Has this been fixed? we are seeing similar after upgrading to 14.4.13.3468.

Created on Jan 5, 2015 1:15:50 AM by  Jason Horne (0) 1



Votes:

0

Your Vote:

Up

Down

Hi,

There is no known issue with the latest version of PRTG (14.4.13.3800+). Please forward your log files for analysis. Start the tool PRTG Administrator and click on the Send Logs to Paessler button or forward a support bundle by clicking on the Contact Support button in the bottom right corner of your Web GUI or Enterprise Console.

Best regards

Created on Jan 5, 2015 7:14:10 AM by  Felix Saure [Paessler Support]



Please log in or register to enter your reply.


Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.