What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general.

Learn more

PRTG Network Monitor

Intuitive to Use. Easy to manage.
More than 500,000 users rely on Paessler PRTG every day. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free Download

Top Tags


View all Tags

Failover Cluster node regular has "Cluster Node Disconnected" error

Votes:

0

We recently setup a PRTG Failover Cluster node and everything connected and setup fine. We have been getting an error regularly overnight where the Cluster node will show up as the Cluster Probe device being disconnected for a short period of time and then re-establish. We have been unable to find any cause for this and was wondering if anyone else experienced this and may have found a reason. Windows logs and PRTG logs do not seem to show any reason.

cluster clustering failover

Created on Apr 27, 2016 7:19:08 AM



4 Replies

Votes:

0

Hello,

Please forward us also a Support Bundle from both cluster nodes for analysis. This can be done via the "Contact Support" ribbon in the lower right corner of the failover´s web interface. Please refer to this kb post.

Created on Apr 28, 2016 10:43:39 AM by [email protected]



Votes:

0

Below is a copy off error we get. Have Uploaded support bundle as well Cluster Probe > Cluster Probe > Cluster Probe Device (127.0.0.1)

Sensor Cluster Health (Cluster Health) * New Status at 29/04/2016 2:43:43 AM (AUS Eastern Standard Time): Down ended (now: Down Partial) Last Message: 1 # (Cluster Nodes Disconnected) is above the error limit of 0 # in Cluster Nodes Disconnected

Last Scan: Last Up: Last Down: Uptime: Downtime: Coverage: Sensor Type: Interval: 60 s 60 s 120 s 99.4755% 0.5245% 100% Cluster Health 60 s

Check Now Acknowledge Alarm Pause Resume

Pause for 5 minutes Pause for 60 minutes Pause for 24 hours

Channel Last Value Cluster Messages In 9 Msg/min Cluster Messages Out 10 Msg/min Cluster Nodes Disconnected 1 # Connects 1 #/min Downtime Outbound Cluster Connections 1 #

History 29/04/2016 1:55:43 AM Down, 1 # (Cluster Nodes Disconnected) is above the error limit of 0 # in Cluster Nodes Disconnected 29/04/2016 1:55:43 AM Down, 1 # (Cluster Nodes Disconnected) is above the error limit of 0 # in Cluster Nodes Disconnected 29/04/2016 1:48:57 AM Up, 1 # 29/04/2016 1:47:43 AM Up, 1 # 29/04/2016 1:47:43 AM Up, 1 # 29/04/2016 1:35:43 AM Down Partial, 1 # (Cluster Nodes Disconnected) is above the error limit of 0 # in Cluster Nodes Disconnected

Don't want to receive this email? Please edit the triggers of this sensor or edit your notification settings!

Created on Apr 29, 2016 2:10:00 AM



Votes:

0

?? What was the result of this?? I'm having a similar issue. many times a day my cluster health sensor goes down. Indicating the same error "Cluster nodes Disconnected".

Created on Mar 31, 2020 7:19:55 PM



Votes:

0

In that case the issue was that the Failover occasionally lost connection due to network problems. Please check the connection between the two nodes.

Created on Apr 1, 2020 10:37:25 AM by Sasa Ignjatovic [Paessler Support]




Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.