What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general.

Learn more

PRTG Network Monitor

Intuitive to Use. Easy to manage.
More than 500,000 users rely on Paessler PRTG every day. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free Download

Top Tags


View all Tags

SNMP Advanced Division/Multiplication

Votes:

0

Hi Team,

Is it possible to in the future look at adding the feature of adding the division and multiplications of results for SNMP Advanced ?

I've used this to map data from a heat exchanger however its reporting temps of 134c and 168c where it should be 13.4c and 16.8. I can get around this by doing individual sensors for each temp and then into one sensor with sensor factory, but this would be nicer to simply be able to do it in the advanced sensor one day.

Cheers,

Nick

advanced snmp snmp-advanced

Created on May 11, 2016 8:48:45 PM

Last change on Jul 25, 2016 6:04:54 AM by  Luciano Lingnau [Paessler]



Best Answer

Accepted Answer

Votes:

0

This solution applies to PRTG Network Monitor 16.1.22 or later

Please be aware that this field is only visible for channels in a custom unit (Sometimes this needs to be defined in the sensor's settings first). As soon as the unit is defined as custom the multiplication/division settings will appear in the channel's settings.

And this option is not available for the following sensors which provide the scaling factor within their sensor settings:

  • Sensor Factory Sensor
  • SNMP APC Hardware Sensor
  • SNMP Custom Sensor
  • SNMP Dell Hardware Sensor
  • SNMP Library Sensor
  • WMI Custom Sensor

Best Regards,

Created on May 13, 2016 7:36:42 AM by  Luciano Lingnau [Paessler]

Last change on Jul 25, 2016 6:10:04 AM by  Luciano Lingnau [Paessler]



3 Replies

Votes:

0

Hello Nick,
we appreciate your contact.

As we don't want to increase the complexity of the sensor's setup we will most likely never introduce this option in the sensor's settings, but as of recent PRTG versions it is possible to configure a Scaling Multiplication/Division in the Channel's settings to achieve the very same results.

Best Regards,

Created on May 12, 2016 6:46:59 AM by  Luciano Lingnau [Paessler]



Votes:

0

Hi Luciano,

The scaling option would be perfect for me to use, however I have found that it doesn't display on our installation. We're running the latest version 16.2.24. I've had a look in both standard SNMP Custom sensors and the Advanced ones and can't see the options. http://iforce.co.nz/i/jtdptrm3.kic.png

Can you confirm I'm not missing anything or need to enable any extra features ?

Cheers,

Created on May 12, 2016 8:18:05 PM



Accepted Answer

Votes:

0

This solution applies to PRTG Network Monitor 16.1.22 or later

Please be aware that this field is only visible for channels in a custom unit (Sometimes this needs to be defined in the sensor's settings first). As soon as the unit is defined as custom the multiplication/division settings will appear in the channel's settings.

And this option is not available for the following sensors which provide the scaling factor within their sensor settings:

  • Sensor Factory Sensor
  • SNMP APC Hardware Sensor
  • SNMP Custom Sensor
  • SNMP Dell Hardware Sensor
  • SNMP Library Sensor
  • WMI Custom Sensor

Best Regards,

Created on May 13, 2016 7:36:42 AM by  Luciano Lingnau [Paessler]

Last change on Jul 25, 2016 6:10:04 AM by  Luciano Lingnau [Paessler]




Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.