What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general.

Learn more

PRTG Network Monitor

Intuitive to Use. Easy to manage.
More than 500,000 users rely on Paessler PRTG every day. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free Download

Top Tags


View all Tags

snmp traffic sensor bintec lan interfaces missing

Votes:

0

when adding a snmp traffic sensor for a bintec router there is no lan Interface or Bridge Interface offered (only vpn Interfaces). in older Versions of prtg (maybe bintec Releases) you could easily add a bandwidth sensor for bintec lan Interfaces.

is there any solution? thank you.

chris

bintec prtg snmp-traffic

Created on Jun 20, 2017 7:26:25 AM



Best Answer

Accepted Answer

Votes:

1

Problem solved:
device Settings -> snmp compatibility Options -> only use 32 bit counters

Created on Jun 28, 2017 12:53:06 PM

Last change on Jun 28, 2017 1:07:53 PM by Luciano Lingnau [Paessler]



4 Replies

Votes:

0

Hello Chris, we appreciate your contact.

Please download the "SNMP Tester" from our website and issue a "Scan Interfaces" test. Please share the outcome.

Best Regards,
Luciano Lingnau [Paessler Support]

Created on Jun 21, 2017 10:56:28 AM by Luciano Lingnau [Paessler]



Votes:

0

Hello Luciano,

Here are the results: https://1drv.ms/t/s!AuErojgNfCvOrWdwtEyJ35KN44MD

LAN Interfaces missing ... same result like in prtg ...

Thank you.

Kind regards, Chris

Created on Jun 21, 2017 7:12:59 PM



Votes:

0

Hello Chris,
thank you for your reply.

That confirms that these are the only interfaces present in the ifTable and ifXTable of the IF-MIB on your device:

Found standard interfaces:
30010001: (30010001) DSL1,Connected,0 KBit/s,PPP,, 64 Bit
38100001: (38100001) IPSEC1,Not Connected,0 KBit/s,Tunnel,, 64 Bit
38100002: (38100002) IPSEC2,Connected,0 KBit/s,Tunnel,, 64 Bit
38100003: (38100003) IPSEC3,Connected,0 KBit/s,Tunnel,, 64 Bit
38100004: (38100004) IPSEC4,Connected,0 KBit/s,Tunnel,, 64 Bit
38100005: (38100005) IPSEC5,Connected,0 KBit/s,Tunnel,, 64 Bit
38100006: (38100006) IPSEC6,Connected,0 KBit/s,Tunnel,, 64 Bit

I encourage you to contact the vendor and inquiry about polling the LAN interfaces over SNMP.

Best Regards,
Luciano Lingnau [Paessler Support]

Created on Jun 22, 2017 7:28:17 AM by Luciano Lingnau [Paessler]



Accepted Answer

Votes:

1

Problem solved:
device Settings -> snmp compatibility Options -> only use 32 bit counters

Created on Jun 28, 2017 12:53:06 PM

Last change on Jun 28, 2017 1:07:53 PM by Luciano Lingnau [Paessler]




Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.