New Question
 
 
PRTG Network Monitor

Intuitive to Use.
Easy to manage.

200.000 administrators have chosen PRTG to monitor their network. Find out how you can reduce cost, increase QoS and ease planning, as well.

Free PRTG
Download >>

 

What is this?

This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general. You are invited to get involved by asking and answering questions!

Learn more

 

Top Tags


View all Tags


how to add Radio local loop on my prtg

Votes:

0

Your Vote:

Up

Down

hi I add the address of the local radio loop but nothing to display or detect in my prtg. how can I proceed.

blr monitoring prtg

Created on Jun 25, 2018 3:17:53 PM by  nafoua (0) 1



9 Replies

Votes:

0

Your Vote:

Up

Down

Dear nafoua,

PRTG cannot automatically detect an address if it is not available as IP and responds to an ICMP ping. Please check if that is the case.

Created on Jun 26, 2018 6:43:44 PM by  Arne Seifert [Paessler Support]



Votes:

0

Your Vote:

Up

Down

yes, it is an IP address and responds to ICMP ping

Created on Jun 29, 2018 8:44:04 AM by  nafoua (0) 1



Votes:

0

Your Vote:

Up

Down

Dear nafoua,

when you add a device with that IP to PRTG, can you at least add a ping sensor then?

Regarding other sensors, do you know which protocols are offered by the radio loop?

Created on Jun 29, 2018 1:56:20 PM by  Arne Seifert [Paessler Support]



Votes:

0

Your Vote:

Up

Down

yes I can add it but the ping sensor is displayed as unknown ... for the second question: I think it's the SNMP protocol

Created on Jul 4, 2018 10:13:38 AM by  nafoua (0) 1



Votes:

0

Your Vote:

Up

Down

Dear nafoua,

in this case, please check if you can read the device with the SNMP Tester. You can try to read the device uptime, or perform a walk on 1.3.6

Please make sure to enter the correct SNMP credentials. Do you get any response?

Created on Jul 4, 2018 5:05:03 PM by  Arne Seifert [Paessler Support]



Votes:

0

Your Vote:

Up

Down

im getting this error message:

Paessler SNMP Tester 5.2.3 Computername: SUPERVISION Interface: (192.168.1.20)
7/6/2018 11:00:37 AM (3 ms) : Device: 192.168.1.20
7/6/2018 11:00:37 AM (5 ms) : SNMP V2c
7/6/2018 11:00:37 AM (6 ms) : Walk 1.3.6.1.2.1.2
7/6/2018 11:00:39 AM (2019 ms) : Error: -2003

Created on Jul 6, 2018 11:07:10 AM by  nafoua (0) 1

Last change on Jul 6, 2018 11:13:01 AM by  Luciano Lingnau [Paessler Support]



Votes:

0

Your Vote:

Up

Down

Dear nafoua,

error -2003 means that the device did not response in time, or at all. Possible causes include

  • wrong device address
  • wrong SNMP port / credentials
  • SNMP agent on the device does not run
  • or is not configured correctly
  • or responds too slow

That is not very specific, but these are the things to look for. Regarding a possible slow response, please try the increase the timeout setting. If that does not help, please check the other possible causes.

Created on Jul 6, 2018 11:14:34 AM by  Arne Seifert [Paessler Support]

Last change on Jul 6, 2018 11:15:13 AM by  Arne Seifert [Paessler Support]



Votes:

0

Your Vote:

Up

Down

always the same erreur-2003

Created on Jul 10, 2018 10:23:20 AM by  nafoua (0) 1



Votes:

0

Your Vote:

Up

Down

Dear nafoua,

in this case, one cannot communicate with that device via SNMP, I am sorry.

Created on Jul 10, 2018 1:25:29 PM by  Arne Seifert [Paessler Support]



Please log in or register to enter your reply.


Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available.